Banner Engineering SM2A912LVAGQD Valu-Beam® 912 Photoelectric Sensor, Rectangle Shape, 0.3 to 4.5 m Sensing, Visible Red Sensing Beam

Photoelectric Retroreflective Sensors
139556 MFG #: SM2A912LVAGQD
BANNER®
308.25000 / ea
Banner_SM2A912LVAGQD
  • Catalog Number: SM2A912LVAGQD
  • Connection: 3-Pin Mini-Style Quick Disconnect
  • Country of Origin: USA
  • Enclosure: IEC IP66 NEMA 1, 2, 3, 3S, 4, 4X, 12 And 13 Reinforced Thermoplastic Polyester
  • Environmental Conditions: 90 PCT At 50 ° C Relative Humidity
  • Gross Weight Per Pack: 1 lb
  • Leakage Current: Off-State Output: Less Than 1.7 MILAMP
  • Lens: Acrylic
  • Operating Temperature: -20 To 70
  • Size: 36.6 MM Length X 35.6 MM Width X 77.5 MM Height
  • Standards: CE Marked, CSA Certified, cULus Listed, RoHS Complaint
  • Type: 912 Series Polarized Retroreflective Mode Photoelectric Sensor
  • UNSPSC: 39121528
  • UPC 11: 66248826653
  • UPC 12: 66248826653
  • Voltage Rating: 24 - 250 V
  • Stock Status: NONSTOCK
  • Brand: BANNER®
  • Manufacturer: Banner Engineering Corp.
  • Response Time: 4
  • Sensing Beam: 650 NMTR Visible Red
  • Sensing Range: 0.3 - 4.5
Banner Engineering Valu-Beam® Photoelectric Sensor, Series: 912, Rectangle, Retro Reflective Sensing Method, 0.3 to 4.5 m Sensing Range, Visible Red Sensing Beam, 4 ms Response, Switch Output, 24/250 VAC, 20 mA, 50/60 Hz, Quick-Disconnect, LED Light Source, 36.6 mm L x 35.6 mm W x 77.5 mm H, NEMA 1/2/3/3S/4/4X/12/13/IP66, -20 to 70 deg C Operating, Environmental Conditions: 90 Percent at 50 deg C
QTY
Add to Wishlist
  • Features
Protected against transient voltages and false pulse on power-up; Stainless steel hardware; 912 Series ac sensors can be destroyed from overload conditions; Use on low voltage requires careful analysis of the load to determine if the leakage current or on-state voltage of the sensor will interfere with proper operation of the load; The false-pulse protection feature may cause momentary drop-out of the load when the sensor is wired in series or parallel with mechanical switch contacts; Potentiometer located at rear of sensor
Less than or equal to 5 V RMS at 750 mA load and less than or equal to 10 V RMS at 15 mA load on-state voltage drop
Protected against transient voltages and false pulse on power-up
Stainless steel hardware
912 Series ac sensors can be destroyed from overload conditions
Use on low voltage requires careful analysis of the load to determine if the leakage current or on-state voltage of the sensor will interfere with proper operation of the load
The false-pulse protection feature may cause momentary drop-out of the load when the sensor is wired in series or parallel with mechanical switch contacts
Potentiometer located at rear of sensor
912 series polarized retroreflective mode photoelectric sensor
Less than 1.7 mA off-state output leakage
4 ms on/off response time
650 nm visible red LED sensing beam
Acrylic lens, 90 percent at 50 deg C (non-condensing) relative humidity
3-pin mini-style quick disconnect connection
Reinforced thermoplastic polyester enclosure
Light/dark operate
SPST SCR solid-state 2-wire output, 10 mA minimum load current, 750 mA to 50 deg C, 500 mA to 70 deg C maximum steady-state load capability, 4 A for 1 Sec (non-repetitive) inrush capability